MTHTrains 4-6-0 Steam Freight/Passenger Set Troubleshooting Guide

4-6-0 Steam Freight/Passenger SetOperation Manual (3V PS2)FYSPSAPLEASE READ BEFORE USE AND SAVEwww.mthtrains.com

Freight Yard Sounds (FYS) or Passenger Station Announcements (PSA): Your engine is equipped with a sound package of either freight yard or passenger

FireRearCoupler=Rear Coupler:To fire the rear coupler, press the CPLR Button on the remote and then press the end of the throttle control. The soun

DO NOTOVER OILDO NOTOVER OILMaintenanceLubrication InstructionsThe engine should be oiled and greased in order to run properly.Regularly lubricate all

Cleaning The Wheels, Tires, and TrackPeriodically check the locomotive wheels and pickups for dirt and buildup, which can cause poor electrical contac

!Remove the side rods (the rods that connect each drive wheel to the other) from the wheels in order to slip the new tire over the grooved drive wheel

ProtoSmoke™ Unit OperationThe engine contains a Proto-Sound® 2.0 controlled smoke unit that outputs smoke through the smokestack on the roof of the

After removing the engine from storage, add another 25 drops of fluid, letting the wick soak up the fluid for 15 minutes prior to operation.If you ex

Locomotive Light Bulb ReplacementRemove the 4 screws, then lift the body away from the chassis. 2) Once the locomotive boiler has been removed from it

STEP2Remove these two screwsRemove these two screwsSTEP3STEP42) With the four screws removed, lower the chassis from the shell, take care not to pull

C1) Remove the four (4) screws located under the caboose's trucks.2) Lower the chassis from the shell, taking care not to pull the wires out.3) C

Table of ContentsSet Up Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Getting Started. . . .

5) Replace the bulb by pushing the socket up at an angle from the bulb holder and pulling the bulb from its socket. Replace with a new bulb and rev

Replace: If the sounds are not improved at the end of the 15-minute test charge, it is time to replace the battery. Available through M.T.H. Parts:

DCS Remote Commander The following Guide will help you trouble shoot your DCS Remote Commander handheld remote.Troubleshooting GuideWARNING – DO NOT C

Troubleshooting Proto-Sound® 2.0 ProblemsAlthough Proto-Sound® 2.0 has been designed and engineered for ease of use, you may have some questions duri

FYS/PSA RemedyOnce in FYS/PSA, the engine doesn’t go into reverse.When the FYS/PSA enters its last sequence the bell automatically comes on.When FYS/P

TransformerModelCenter Rail Outside RailMin/Max.VoltagePowerRatingTransformerTypeLionel 1032 U A 5-16v 90-Watt StandardLionel 1032M U A 5-16v 90-Watt

Additional Features Accessible With The DCS Remote Control System(Additional equipment required)While conventional mode operation of a Proto-Sound® 2

Quick-Start DVDThe included Quick-Start DVD demonstrates the start-up and basic operation of this set as well as other information about model railro

Service & Warranty InformationHow to Get Service Under the Terms of the Limited One-Year WarrantyWhen you suspect an item is defective, please ch

You can obtain replacement parts and replacement instructions from the M.T.H. Parts Department (Order online: www.mth-railking.com, e-mail: parts@mt

Gently push together RealTraxInsert lock-on into knock-out tab(Lock-on is the interface between the track and transformer)Make sure the metal contacts

Running the engine without primed Smoke unit may cause damageAdd Smoke fluidSmoke Unit Control(on bottom of tender)Priming the Smoke UnitYou should pr

Placing the Engine on the TrackPlace the engine on the track, then insert the reverse unit plug that extends out of the tender into the receptacle at

RailKing 4-6-0 Steam Freight/Passenger Set with Proto-Sound® 2.07Connecting the Transformer & Installing DCS Remote Commander SetYour set comes wi

RailKing 4-6-0 Steam Freight/Passenger Set with Proto-Sound® 2.08Basic OperationAfter making sure everything is properly assembled, aim the Remote at

Operation Buttons Using the Remote HandheldSTART UP/SHUT DOWN (SU/SD)- Pressing this button will start your engine. Its lights, sound and smoke (if eq